AS568-471 FFKM O-Ring — 557.66 × 6.99 mm
A very thick section for the largest diameters and most severe static sealing duties. With an inside diameter of 557.66 mm and a 6.99 mm cross section, this is a very-large seal for the largest diameters and heavy static service. Moulded from Aperflu 2275 perfluoroelastomer (FFKM) for continuous service up to 200 °C, this seal resists hot acids, caustics, solvents, fuels and steam.
Dimensions
| Dash number | AS568-471 |
|---|---|
| Inside diameter (ID) | 557.66 mm (21.955 in) |
| Cross section (CS) | 6.99 mm (0.275 in) |
| Outside diameter (OD) | 571.64 mm (22.506 in) |
| Material | Aperflu 2275 perfluoroelastomer (FFKM) |
| Service temperature | up to 200 °C continuous |
Pharmaceutical and food processing
Steam-in-place and clean-in-place cycles, aggressive cleaning agents and potent active pharmaceutical ingredients (APIs) demand a seal that stays inert and dimensionally stable. Aperflu 2275 is suited to product-contact and CIP/SIP duties where extractables must be kept to a minimum.
Why Aperflu 2275 FFKM
Compared with bisphenol-cured FKM, peroxide-cured FFKM keeps its sealing force longer at temperature — critical for static and slow-dynamic duty in chemical service.
Typical applications
Large-diameter flanges, autoclave and reactor seals, structural static joints, where Aperflu 2275 outperforms FKM and EPDM in aggressive media and elevated temperature.
Compound properties
| Property | Typical value | Test method |
|---|---|---|
| Hardness | 70 – 71 Shore A | GB/T 39693.4 |
| Tensile strength | 21.2 – 21.8 MPa | GB/T 528 (dumbbell type 2) |
| Elongation at break | 155 – 170 % | GB/T 528 (dumbbell type 2) |
| Compression set, 200 °C × 70 h (25 %, method B) | 15 – 16 % | GB/T 7759.1 |
All values are typical. Every batch is shipped with an individual certificate of analysis and may differ from the typical values listed here.
Chemical resistance
The fully fluorinated backbone of Aperflu 2275 resists the aggressive media that attack FKM, EPDM and silicone — including concentrated hydrochloric, nitric, sulfuric and glacial acetic acids, strong caustics, and a broad range of solvents and fuels. Refer to the rating table below for guidance, and confirm your exact media with our engineers.
| Media group | Rating |
|---|---|
| Hydrochloric acid | Excellent |
| Nitric acid | Excellent |
| Sulfuric acid | Excellent |
| Acetic acid (glacial) | Excellent |
| Other hot organic & inorganic acids | Excellent |
| Caustics (ammonia, NaOH up to 50 %) | Excellent |
| Ketones, aldehydes, esters, ethers, alcohols | Excellent |
| Solvents, fuels, hydrocarbons, sour gases | Excellent |
| Steam and hot water | Excellent |
| Ethylene diamine & high-temp amines | Good – contact us for grade selection |
| Clean-in-place (CIP) / steam-in-place (SIP) agents | Excellent |
| Active pharmaceutical ingredients (APIs) | Excellent |
Ratings are typical for peroxide-cured FFKM compounds at room and elevated temperature. Final suitability depends on concentration, temperature and pressure — contact us for a compound recommendation against your specific media.
Need AS568-471 in a custom colour or quantity?
Tell us your dash number, quantity and service media. We quote within 24 hours.
Request a Quote